Coverart for item
The Resource Stainless-steel pipe, 1/2 in. (13 mm) and larger

Stainless-steel pipe, 1/2 in. (13 mm) and larger

Label
Stainless-steel pipe, 1/2 in. (13 mm) and larger
Title
Stainless-steel pipe, 1/2 in. (13 mm) and larger
Contributor
Subject
Language
eng
Member of
Cataloging source
E7B
Illustrations
illustrations
Index
no index present
LC call number
TS280
LC item number
.S73 2012eb
Literary form
non fiction
Nature of contents
dictionaries
http://library.link/vocab/relatedWorkOrContributorName
  • American Water Works Association
  • American National Standards Institute
Series statement
AWWA Standard C220
Series volume
v. 12
http://library.link/vocab/subjectName
  • Pipe, Steel
  • Water-pipes
  • Pipe, Steel
  • Water-pipes
Label
Stainless-steel pipe, 1/2 in. (13 mm) and larger
Instantiates
Publication
Note
  • "ANSI/AWWA C220-12 (revision of ANSI/AWWA C220-07)."
  • At head of title: AWWA standard
  • "Effective date: June 1, 2012. First edition approved by AWWA Board of Directors June 18, 1992. This edition approved Jan. 22, 2012. Approved by American National Standards Institute March 27, 2012."
Carrier category
online resource
Carrier category code
  • cr
Carrier MARC source
rdacarrier
Color
multicolored
Content category
text
Content type code
  • txt
Content type MARC source
rdacontent
Contents
  • Foreword -- I. Introduction. -- I.A. Background -- I.B. History -- I.C. Acceptance -- II. Special Issues -- II. A. Basis of Design -- III. Use of This Standard -- III. A. Purchaser Options and Alternatives -- III. B. Modification to Standard -- IV. Major Revisions -- V. Comments -- Section 1 : GENERAL -- Sec. 1.1 Scope -- Sec. 1.2 Purpose -- Sec. 1.3 Application -- Section 2: REFERENCES -- Section 3: DEFINITIONS -- Section 4: REQUIREMENTS -- Sec. 4.1 Permeation -- Sec. 4.2 Materials -- Sec. 4.3 General Fabrication Requirements
  • Sec. 4.4 Specific Fabrication RequirementsSec. 4.5 Permissible Variations in Weights and Dimensions -- Sec. 4.6 Preparation of Ends -- Sec. 4.7 Special Ends -- Sec. 4.8 Cleaning and Descaling -- Sec. 4.9 Specials and Fittings -- Section 5: VERIFICATION -- Sec. 5.1 Inspection -- Sec. 5.2 Test Procedures -- Sec. 5.3 Basis for Rejection -- Sec. 5.4 Repair of Defects -- Section 6: DELIVERY -- Sec. 6.1 Marking -- Sec. 6.2 Shipping, Storage, and Handling -- Sec. 6.3 Affidavit of Compliance -- Figures
  • Figure 1 Repair method by offset value and well thickenss Figure 2 Reduced-section tension test specimen -- Figure 3 Guided-bend test specimen -- Figure 4 Jig for guided-bend test -- Figure 5 Alternative guided-bend wraparound jig -- Figure 6 Alternative guided-bend roller jig -- Tables -- Table 1 Mechanical properties for austenitic or duplex stainless steel -- Table 2 Re pair requirements based on offset value and wall thickness -- Table 3 Guided-bend test jig dimensions
Control code
802058901
Dimensions
unknown
Extent
1 online resource (xii, 21 pages)
Form of item
online
Isbn
9781583218846
Media category
computer
Media MARC source
rdamedia
Media type code
  • c
Other physical details
illustrations
Specific material designation
remote
System control number
(OCoLC)802058901
Label
Stainless-steel pipe, 1/2 in. (13 mm) and larger
Publication
Note
  • "ANSI/AWWA C220-12 (revision of ANSI/AWWA C220-07)."
  • At head of title: AWWA standard
  • "Effective date: June 1, 2012. First edition approved by AWWA Board of Directors June 18, 1992. This edition approved Jan. 22, 2012. Approved by American National Standards Institute March 27, 2012."
Carrier category
online resource
Carrier category code
  • cr
Carrier MARC source
rdacarrier
Color
multicolored
Content category
text
Content type code
  • txt
Content type MARC source
rdacontent
Contents
  • Foreword -- I. Introduction. -- I.A. Background -- I.B. History -- I.C. Acceptance -- II. Special Issues -- II. A. Basis of Design -- III. Use of This Standard -- III. A. Purchaser Options and Alternatives -- III. B. Modification to Standard -- IV. Major Revisions -- V. Comments -- Section 1 : GENERAL -- Sec. 1.1 Scope -- Sec. 1.2 Purpose -- Sec. 1.3 Application -- Section 2: REFERENCES -- Section 3: DEFINITIONS -- Section 4: REQUIREMENTS -- Sec. 4.1 Permeation -- Sec. 4.2 Materials -- Sec. 4.3 General Fabrication Requirements
  • Sec. 4.4 Specific Fabrication RequirementsSec. 4.5 Permissible Variations in Weights and Dimensions -- Sec. 4.6 Preparation of Ends -- Sec. 4.7 Special Ends -- Sec. 4.8 Cleaning and Descaling -- Sec. 4.9 Specials and Fittings -- Section 5: VERIFICATION -- Sec. 5.1 Inspection -- Sec. 5.2 Test Procedures -- Sec. 5.3 Basis for Rejection -- Sec. 5.4 Repair of Defects -- Section 6: DELIVERY -- Sec. 6.1 Marking -- Sec. 6.2 Shipping, Storage, and Handling -- Sec. 6.3 Affidavit of Compliance -- Figures
  • Figure 1 Repair method by offset value and well thickenss Figure 2 Reduced-section tension test specimen -- Figure 3 Guided-bend test specimen -- Figure 4 Jig for guided-bend test -- Figure 5 Alternative guided-bend wraparound jig -- Figure 6 Alternative guided-bend roller jig -- Tables -- Table 1 Mechanical properties for austenitic or duplex stainless steel -- Table 2 Re pair requirements based on offset value and wall thickness -- Table 3 Guided-bend test jig dimensions
Control code
802058901
Dimensions
unknown
Extent
1 online resource (xii, 21 pages)
Form of item
online
Isbn
9781583218846
Media category
computer
Media MARC source
rdamedia
Media type code
  • c
Other physical details
illustrations
Specific material designation
remote
System control number
(OCoLC)802058901

Library Locations

    • Curtis Laws Wilson LibraryBorrow it
      400 West 14th Street, Rolla, MO, 65409, US
      37.955220 -91.772210
Processing Feedback ...